Compex Advanced SerialRAID Adapters SA33-3285-02 Spécifications Page 93
- Page / 457
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
If you do not get an SRN, the disk formatting may be incompatible with the
system (the disk was most likely formatted on a different type of using system).
1) Format the pdisk.
2) Issue the system cfgmgr command.
3) Retry the Configuration Verification service aid.
3. If the problem remains, a software error has probably occurred. Call your support
center for assistance.
Step 2010-3
Have the system diagnostics or problem determination procedures given you a
5-digit SRN for the SSA hot-swap disk drive?
NO Go to “Step 2010-4”.
YES Go to “Service Request Numbers (SRNs)” on page 411.
Step 2010-4
If the system diagnostics are available, go to “Step 2010-5”.
If the stand-alone diagnostics are available, but the system diagnostics are not
available, run the stand-alone diagnostics, then go to “Step 2010-5”.
If the system diagnostics and stand-alone diagnostics are not available, go to “Step
2010-1” on page 72.
Step 2010-5
Run the diagnostics in the problem determination mode.
Note: Do not run the advanced diagnostics, because errors are logged on other using
systems that share the same loop.
Did the diagnostics give you a 5-digit SRN for the SSA hot-swap disk drive?
NO Go to “Step 2010-6”.
YES Go to “Service Request Numbers (SRNs)” on page 411.
Step 2010-6
Are all LEDs off on the drives in a 6 pack?
NO Go to step “Step 2010-9” on page 74.
YES Go to “Step 2010-7”.
Step 2010-7
Are any power cables loose or in need of replacement?
NO Go to “Step 2010-8” on page 74.
Chapter 3. Maintenance Analysis Procedures 73
- Bull ESCALA 1
- Contents 5
- Contents v 7
- Contents vii 9
- Service Guide 10
- Contents ix 11
- Safety Notices 13
- Electrical Safety 14
- Laser Safety Information 14
- Laser Compliance 14
- Preface xiii 15
- About This Book 19
- Trademarks 20
- Overview 21
- Bus Architecture 22
- Microprocessor 22
- Operator Panel 24
- Input/Output Ports 24
- Security Features 24
- Processor Card (1 way only) 25
- Memory Card 25
- (1 only is optional) 25
- 6 Service Guide 26
- Power Flow 27
- Powering Off the System 28
- Powering On the System 28
- Console Strategy 29
- Power-On Self-Test 29
- POST Indicators 29
- POST Keys 30
- System Unit Locations 32
- Front View 32
- Rear View 33
- System Board 34
- System Memory 35
- Physical Location Codes 36
- Location Code Format 36
- AIX Location Codes 38
- Power Supply Locations 40
- System Board Locations 41
- 22 Service Guide 42
- System Location Codes 44
- 26 Service Guide 46
- 28 Service Guide 48
- Specifications 49
- Dimensions 49
- 30 Service Guide 50
- Acoustics 51
- System Service Clearances 51
- External AC Power Cables 51
- Service Inspection Guide 51
- 32 Service Guide 52
- Checkpoints 54
- FRU Isolation 55
- 36 Service Guide 56
- Entry MAP 57
- Fast Path MAP 58
- 40 Service Guide 60
- POST indicators 62
- Diagnostic Information 62
- Purpose of this MAP 64
- Step 1020-2 67
- Step 1020-3 67
- Step 1020-4 67
- MAP 1520: Power 68
- Step 1520-1 68
- Step 1520-2 69
- Step 1520-3 69
- Step 1520-4 70
- Step 1520-5 70
- Step 1520-6 71
- Step 1520-7 71
- Step 1540-1 73
- Step 1540-2 73
- 54 Service Guide 74
- Step 1540-3 75
- Step 1540-4 75
- Step 1540-5 76
- Step 1540-6 77
- Step 1540-7 77
- Step 1540-8 78
- Step 1540-9 79
- Step 1540-10 79
- Step 1540-11 80
- Step 1540-12 81
- Step 1540-13 82
- Step 1540-14 82
- Step 1540-15 83
- Step 1540-16 84
- Step 1540-17 85
- Step 1540-18 85
- Step 1540-19 86
- Step 1540-20 86
- Step 1540-21 87
- Step 1540-22 87
- Step 1540-23 87
- Step 1540-24 87
- Step 1540-25 88
- Step 1540-26 88
- Step 1540-27 89
- Step 1540-28 89
- Using SSA MAPs 90
- Step 2010-1 92
- Step 2010-2 92
- Step 2010-3 93
- Step 2010-4 93
- Step 2010-5 93
- Step 2010-6 93
- Step 2010-7 93
- Step 2010-8 94
- Step 2010-9 94
- Step 2010-10 94
- Step 2010-11 94
- Step 2010-12 94
- Step 2010-13 95
- Step 2323-1 95
- Step 2323-2 95
- Step 2323-3 96
- Chapter 4. Checkpoints 97
- Service Processor Checkpoints 99
- 80 Service Guide 100
- 82 Service Guide 102
- 84 Service Guide 104
- Firmware Checkpoints 105
- 86 Service Guide 106
- 88 Service Guide 108
- 90 Service Guide 110
- 92 Service Guide 112
- 94 Service Guide 114
- Boot Problems and Concerns 116
- Diagnostic Information for 117
- Multiple Bus Systems 117
- 98 Service Guide 118
- Four-Character Checkpoints 119
- Operator Panel Replacement 119
- Replacing the Network Adapter 119
- Determining Location Code 119
- 100 Service Guide 120
- Performing Slow Boot 121
- Confirming Initial Error Code 121
- Memory-Related Error Codes 122
- Operator Panel Error Codes 123
- SPCN Error Codes 124
- 106 Service Guide 126
- 108 Service Guide 128
- 110 Service Guide 130
- Firmware Error Codes 131
- 112 Service Guide 132
- 114 Service Guide 134
- 116 Service Guide 136
- Bus Systems 137
- 120 Service Guide 140
- 122 Service Guide 142
- 124 Service Guide 144
- 126 Service Guide 146
- 128 Service Guide 148
- 130 Service Guide 150
- Service Processor Error Codes 152
- 134 Service Guide 154
- 136 Service Guide 156
- 138 Service Guide 158
- 140 Service Guide 160
- 142 Service Guide 162
- 144 Service Guide 164
- 146 Service Guide 166
- 148 Service Guide 168
- 150 Service Guide 170
- 152 Service Guide 172
- 154 Service Guide 174
- 156 Service Guide 176
- 158 Service Guide 178
- 160 Service Guide 180
- 162 Service Guide 182
- 164 Service Guide 184
- 166 Service Guide 186
- 168 Service Guide 188
- 170 Service Guide 190
- 172 Service Guide 192
- 174 Service Guide 194
- 176 Service Guide 196
- 178 Service Guide 198
- 180 Service Guide 200
- 182 Service Guide 202
- 184 Service Guide 204
- 186 Service Guide 206
- 188 Service Guide 208
- 190 Service Guide 210
- 192 Service Guide 212
- 194 Service Guide 214
- 196 Service Guide 216
- 198 Service Guide 218
- 200 Service Guide 220
- 202 Service Guide 222
- 204 Service Guide 224
- 206 Service Guide 226
- 208 Service Guide 228
- 210 Service Guide 230
- 212 Service Guide 232
- 214 Service Guide 234
- 216 Service Guide 236
- 218 Service Guide 238
- 220 Service Guide 240
- 222 Service Guide 242
- 224 Service Guide 244
- 226 Service Guide 246
- 228 Service Guide 248
- 230 Service Guide 250
- 232 Service Guide 252
- Common Firmware Error Codes 253
- 234 Service Guide 254
- 236 Service Guide 256
- 238 Service Guide 258
- Scan Log Dump Progress Codes 260
- 242 Service Guide 262
- 244 Service Guide 264
- Service Processor Menus 266
- Menu Inactivity 267
- General User Menu 267
- Privileged User Menus 268
- Main Menu 268
- Service Processor Setup Menu 270
- Passwords 271
- 252 Service Guide 272
- System Power Control Menu 274
- 256 Service Guide 276
- System Information Menu 278
- 1. Memory riser card 1 280
- 2. Memory riser card 2 280
- 98. Return to Previous Menu 280
- 262 Service Guide 282
- 264 Service Guide 284
- Language Selection Menu 285
- Call-In/Call-Out Setup Menu 286
- Modem Configuration Menu 287
- Serial Port Selection Menu 288
- Serial Port Speed Setup Menu 288
- Telephone Number Setup Menu 289
- Call-Out Policy Setup Menu 290
- Customer Account Setup Menu 291
- Service Processor Functions 292
- System Power-On Methods 293
- Boot (IPL) Speed 294
- Failure During Boot Process 294
- System Firmware Updates 296
- System Firmware Surveillance 298
- Operating System Surveillance 298
- Call-Out (Call-Home) 299
- Console Mirroring 300
- System Configuration 300
- Service Processor Error Log 301
- LCD Progress Indicator Log 302
- Pre-Standby Phase 303
- Standby Phase 303
- Bring-Up Phase 304
- Run-Time Phase 305
- 286 Service Guide 306
- Password Utilities 308
- Display Error Log 309
- IP Parameters 310
- Adapter Parameters 311
- 292 Service Guide 312
- SCSI Utilities 313
- Select Console 313
- MultiBoot 314
- Select Software 314
- Software Default 314
- Select Install Device 314
- Select Boot Devices 315
- OK Prompt 316
- Multiboot Startup <OFF> 316
- Select Language 317
- 298 Service Guide 318
- 300 Service Guide 320
- Removing the Covers 321
- 302 Service Guide 322
- Replacing Covers 324
- Hot-Pluggable FRUs 326
- Hot-Pluggable Options 326
- Stopping the System Unit 326
- Disk Drive Options 327
- 308 Service Guide 328
- 310 Service Guide 330
- 312 Service Guide 332
- AIX Documentation 333
- 314 Service Guide 334
- 316 Service Guide 336
- Documentation 337
- PCI Adapter Options 338
- PCI Slot LED Definitions 338
- Removing Adapter Cards 339
- 320 Service Guide 340
- System and Devices 341
- Replacing Adapter Cards 342
- 324 Service Guide 344
- PCI Hot-Plug Manager Access 346
- PCI Hot-Plug Manager Menu 347
- Fans and Fan Fillers 348
- Replacement 348
- Power Supplies 348
- Installing a Redundant Fan 349
- 330 Service Guide 350
- 332 Service Guide 352
- System Memory Options 355
- Memory DIMMs 356
- Removing Memory DIMMs 356
- Processor Card 359
- Operator Panel Cable 362
- PCI Adapter Dividers 363
- System Board Assembly 363
- Internal Disk Drive Bays 364
- 346 Service Guide 366
- 348 Service Guide 368
- SCSI (SES) Drive Bay Cables 369
- 350 Service Guide 370
- C Connector 4 Power Connector 371
- 3 Power Connector 371
- 352 Service Guide 372
- 354 Service Guide 374
- 356 Service Guide 376
- View of Right Side 377
- Internal 377
- SCSI Cable 377
- View of Left Side 377
- 358 Service Guide 378
- Replacing Non-Hot-Plug Drives 379
- 360 Service Guide 380
- 362 Service Guide 382
- 364 Service Guide 384
- Chapter 10. Parts Information 385
- Right Side 386
- 368 Service Guide 388
- Left Side 389
- 370 Service Guide 390
- Note: See 391
- , order number SA23-2769 391
- Accessories 392
- Power Cords 392
- Keyboards and Mouse 394
- Acoustical Noise Emissions 395
- 376 Service Guide 396
- Appendix B. Notices 397
- 378 Service Guide 398
- Testing the Setup 400
- Testing Call-In 400
- Testing Call-Out 400
- Serial Port Configuration 401
- 382 Service Guide 402
- Configuration File Selection 404
- 386 Service Guide 406
- Xon/Xoff Modems 407
- Ring Detection 407
- Terminal Emulators 408
- Recovery Procedures 408
- Transfer of a Modem Session 408
- Recovery Strategy 409
- Prevention Strategy 410
- Sample File modem_m0.cfg 411
- 392 Service Guide 412
- Sample File modem_m1.cfg 413
- 394 Service Guide 414
- Sample File modem_z.cfg 415
- 396 Service Guide 416
- Sample File modem_z0.cfg 417
- 398 Service Guide 418
- Sample File modem_f.cfg 419
- 400 Service Guide 420
- # responses 421
- Sample File modem_f0.cfg 422
- 404 Service Guide 424
- Sample File modem_f1.cfg 425
- 406 Service Guide 426
- 408 Service Guide 428
- Diagnostic 429
- 410 Service Guide 430
- SRN Table 431
- Using the SRN Table 431
- Software and Microcode Errors 431
- 412 Service Guide 432
- 414 Service Guide 434
- Advanced SerialRAID Adapters 436
- SSA Location Code Format 441
- SSA Loops and Links 442
- The SSA Adapter 442
- Disk Drive Module Strings 443
- Rules for SSA Loops 444
- Loops and Data Paths 444
- 426 Service Guide 446
- (continued) 447
- 432 Service Guide 452
- NOM / NAME : Date : 453
- SOCIETE / COMPANY : 453
- ADRESSE / ADDRESS : 453
- 86 A1 40KX 03 456
- ORDER REFERENCE 456
- PLACE BAR CODE IN LOWER 456
- LEFT CORNER 456
Produits connexes et manuels pour Mise en réseau Compex Advanced SerialRAID Adapters SA33-3285-02
(189 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.106 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels