Compex NetPassage WP18 Guide d'installation Page 1

Quick Install Guide Wireless 54Mbps A+G Dualband Access Point with built-in PoE NetPassage WP18

Chapter 2 Let’s Get Going - Hardware Setup 8 Now, turn on your power supply. Notice that the Power and Port 4 (PoE Port) (according to the picture

Chapter 2 Let’s Get Going - Hardware Setup 9 Option Three: Using IEEE 802.3af PoE Injector to supply power to the unit Compex WP18 can be powered u

Chapter 2 Let’s Get Going - Hardware Setup 10 Next, connect the RJ45 Ethernet cable attached to the standard PoE Injector to your PC’s Ethernet ne

Chapter 2 Let’s Get Going - Hardware Setup 11 Connect the power adapter supplied in the IEEE802.3af PoE kit to the main electrical supply and the

Chapter 3 Access to Web-based Interface 12 3: Access to Web-based Interface There are two methods to access to the web-based interface of Compex Ne

Chapter 3 Access to Web-based Interface 13 Select NetPassage WP18 in the Compex Products List section and click on Open Web button. To update and

Chapter 3 Access to Web-based Interface 14 This screen prompts you not to exit your uConfig program while accessing to your web-based interface, or

Chapter 3 Access to Web-based Interface 15 You will then reach the home page of Compex WP18’s web-based interface. Note: Refer to User’s Manual

Chapter 3 Access to Web-based Interface 16 From the Product CD, click on Utilities and select NpFind program to run it. Once your Compex WP18 has

Chapter 4 Panel Views and Descriptions 17 4: Panel Views and Descriptions Front View of NetPassage WP18 in the standing position Name D

i Table of Contents 1: Introduction...1 Packaging Content...

Chapter 4 Panel Views and Descriptions 18 Steady Green The WAN connection is enabled. 2 WAN (Link/Activity LED) Flashing Green Data transmission

Chapter 4 Panel Views and Descriptions 19 Side View of NetPassage WP18 in the standing position Name Description 8 External Antennas 2dBi S

Chapter 4 Panel Views and Descriptions 20 11 1, 2, 3 (Ethernet Ports) Integrated 3-port 10/100Mbps Switching (RJ45) 12 4 POE (PoE Port ) If usin

Chapter 5 Technical Specification 21 5: Technical Specifications Safety and Electromagnetic Conformance • FCC Part 15 SubPart B and SubPart C [fo

Chapter 5 Technical Specification 22 Network Interface WAN Interface: 1 x 10/100 Mbps LAN Interface: 3 x 10/100 Mbps Power over Ethernet : 1 x Po

Chapter 5 Technical Specification 23 Operating Temp: Storage Temp: Operating Humidity: 0ºC to 55ºC -20ºC to 75ºC 10% to 80% RH Humidity (RH – Relat

24 Disclaimer: Compex, Inc. provides this guide without warranty of any kind, either expressed or implied, including but not limited to the implie

25 The transmitter shall not be collocated with other transmitters or antennas. ICES 003 Statement This Class B digital apparatus complies with Ca

26 WARRANTY REGISTRATION CARD Register via the Internet at http://www.cpx.com or http://www.compex.com.sg [M-0088-V2.4C] To activate the warranty,

Manual Number: M-0508-V1.1C Version 1.1 September 2005

Chapter 1 Introduction 1 1: Introduction Compex WP18 Wireless 54Mbps A+G Dualband Access Point with built-in PoE let you have the best of both wor

Chapter 1 Introduction 2 Packaging Content Actual product appearance may slightly differ depending on the hardware version. 1 x Compex WP18

Chapter 2 Let’s Get Going - Hardware Setup 3 2: Let’s Get Going-Hardware Setup Compex WP18 can be powered using either the power adapter or the Co

Chapter 2 Let’s Get Going - Hardware Setup 4 Insert one end of the RJ45 Ethernet cable to any of the LAN ports (1,2 or 3) on your Compex WP18, and

Chapter 2 Let’s Get Going - Hardware Setup 5 Power ON your PC. Notice that the Power and Port 1 or 2 (depending on which port you have connected t

Chapter 2 Let’s Get Going - Hardware Setup 6 Option Two: Using Compex PoE to supply power to the unit Compex Power-Over-Ethernet (PoE) is fully com

Chapter 2 Let’s Get Going - Hardware Setup 7 Next, connect the RJ45 Ethernet cable attached to the Compex PoE Injector to your PC’s Ethernet netwo